Rod Hanger
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1015 (Pin) |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Port3 - Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1200(other) |
0 |
-9999 |
9999 |
Side Mounted
Graphics are identical to 1, except they are all rotated 90 degrees + Angle3 around the local X coordinate (including clamp body, bolts, and so on). The Pin port, at bolt 1, remains the same. The pipe port orientation changes, so Z points down to the structure for the pipe port. A ClampSide1 port is required on the side of the clamp, for connection to the shoe or post, with the same orientation as the pipe port. If Width3 is defined, the ClampSide1 port is retracted so that a shoe or post of Width3 can connect directly to it. If Height3 is defined, a positive offset is in the Z direction of the ClampSide1 port. If both Height3 and Width3 are set, Height3 is used.
-
On shoe or post
-
Horizontal Single Shoe or Narrow Post
-
Angled Single Shoe or Narrow Post
-
Double Shoe or Wide Post
-
-
Hanging with Lug, Clevis, Hole, or Threaded hole
-
Side Attachment, Lug, Clevis, Hole, Threaded Shown Upside Down.
-
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1015 (Pin) |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Port3 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Shoes |
0 |
-9999 |
9999 |
|
Side |
1200 (Other) |
|||
Rod Types |
The Diameter of the rod for connecting to other components. And it is same as RodDiameter Property. |
0 |
Thickness3 |
|
Side |
1001 (IntThdRH) |
|||
1003 (IntThdLH) |
||||
Pin Type |
Dimension not defined. Set to -1 |
Dimension not defined. Set to -9999 |
Dimension not defined. Set to 9999 |
|
Side |
1005 (Pin) |
|||
Lug Types |
Dimension not defined. Set to -1 |
Dimension not defined. Set to -9999 |
Dimension not defined. Set to 9999 |
|
Side |
1007 (Eye) |
Side Mounted - Two Side Ports, Angled or Straight
This configuration has two ports on the ClampSide1 and ClampSide2 and it does not include a port on Bolt 1.
If Angle2 is specified, the ports are located on the side of the clamp, separated by the specified angle. These angled ports are oriented as shown below. Angle2 is always less than 180.
If Width3 is specified, the ports are located on the side of the clamp separated by the specified width and these ports are oriented as shown below. Width3 is always less than the outside diameter of the clamp body (that is, less than Diameter1 + 2 x Thickness1).
In case if both Width3 and Angle2 are specified, Width3 is used.
Angle1 and Angle3 can also be used with this configuration.
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1200 (Other) |
0 |
-9999 |
9999 |
Port3 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1200 (Other) |
0 |
-9999 |
9999 |
Direct Bolted
In Direct Bolted Clamps, the bolt quantities may all be zero since the hanger rods often takes the place of the bolts. The ports are separated by Width3 and centered in the clamp body and with an offset of Height3 from the pipe centerline as shown below. You can also specify bolts in rows 1 to 6 but the ports are located independently of the bolts in this configuration.
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1004 (Rod Hole) |
Dimension not defined. Set to -1 |
Dimension not defined. Set to -9999 |
Dimension not defined. Set to 9999 |
Port3 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1004 (Rod Hole) |
Dimension not defined. Set to -1 |
Dimension not defined. Set to -9999 |
Dimension not defined. Set to 9999 |
Riser Clamp, Rod Hanger
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1005 (Pin) |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Port3 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1005 (Pin) |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Pin or Bolt Diameter |
Riser Clamp on Structure, Socket Clamp, Underground Clamp
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1200 (Other) |
0 |
-9999 |
9999 |
Port3 – Wing Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Wing |
1200 (Other) |
0 |
-9999 |
9999 |
Offset Pipe Clamp
Port1 – Route
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Route |
1016 (Pipe Clamp) |
Pipe Outside Diameter |
Pipe Outside Diameter |
Pipe Outside Diameter |
Port2 – Side Mount Point
Port Name |
Port Type |
Size |
MinSize |
MaxSize |
Side |
1200 (Other) |
0 |
-9999 |
9999 |