Standard Port
The maximum limit of standard ports is two. By default, port 1 is placed at the center of the plate shape on the bottom surface and port 2 is placed at the center of the plate shape on the upper surface.
IJOAhsStandardPort1::P1xOffset
Enter a value to move the port on the X-axis. Both positive and negative values are valid.
IJOAhsStandardPort1::P1yOffset
Enter a value to move the port on the Y-axis. Both positive and negative values are valid.
IJOAhsStandardPort1::P1zOffset
Enter a value to move the port on the Z-axis. Both positive and negative values are valid.
IJOAhsStandardPort1::P1Rotx
Enter a value to rotate the port about the X-axis.
IJOAhsStandardPort1::P1Roty
Enter a value to rotate the port about the Y-axis.
IJOAhsStandardPort1::P1Rotz
Enter a value to rotate the port about the Z-axis.
IJOAhsStandardPort2::P2xOffset
Enter a value to move the port on the X-axis. Both positive and negative values are valid.
IJOAhsStandardPort2::P2yOffset
Enter a value to move the port on the Y-axis. Both positive and negative values are valid.
IJOAhsStandardPort2::P2zOffset
Enter a value to move the port on the Z-axis. Both positive and negative values are valid.
IJOAhsStandardPort2::P2Rotx
Enter a value to rotate the port about the X-axis.
IJOAhsStandardPort2::P2Roty
Enter a value to rotate the port about the Y-axis.
IJOAhsStandardPort2::P2Rotz
Enter a value to rotate the port about the Z-axis.
Route Port
The route port helps to place a plate to a route. Only one route port per plate is allowed.
In the descriptions below, there is reference made to Pipe CL (centerline). While there is no actual Pipe CL, this is the imaginary pipe centerline where you can envision the pipe that you are connecting to running. The Pipe CL is always located off of the bottom edge of the plate shape. All of the offsets are in reference to this Pipe CL.
IJOAhsRoutePort::RPDiameter
Specifies the route diameter. The port is offset from the graphics by this value.
This value does not have to be just the route diameter; it can also include the pad thickness, insulation thickness, etc.
IJOAhsRoutePort::RPOffsetfromPipeCL
Specifies an offset from the Pipe CL moving perpendicular. If a non-zero value is entered, the port will be offset and the graphics of the plate will be extended so that they appear to reach the outside of the diameter specified.
IJOAhsRoutePort::RPOffsetalongPipe
Enter a value to move the port along the Pipe CL. Both positive and negative values are valid.
IJOAhsRoutePort::RPRotationAroundPipe
Enter a value to rotate the pipe port about its X-axis. Both positive and negative values are valid.
IJOAhsRoutePort::RPAdjustPlateLength
Enter the codelist value that specifies whether or not the length of the plate will be adjusted to meet the curve of the route when RPOffsetalongPipe is not 0. Values are 1 meaning yes and 2 meaning no.
Hole Port
The hole port is used only for plates that only connect via holes. This does not include bolt holes. The hole port cannot be offset but it can be rotated about the X, Y or Z axis. There can be a maximum of three hole ports. All of them have the same inputs.
IJOAhsHolePort1::HP1Rotx
Enter a value to rotate the port about the X-axis.
IJOAhsHolePort1::HP1Roty
Enter a value to rotate the port about the Y-axis.
IJOAhsHolePort1::HP1Rotz
Enter a value to rotate the port about the Z-axis.
IJOAhsHolePort1::HP1PosX
Enter the position, from the plates bottom left (0,0,0), in the X direction.
IJOAhsHolePort1::HP1PosY
Enter the position, from the plates bottom left (0,0,0), in the Y direction.
IJOAhsHolePort1::HP1Size
Enter the size of the hole.
IJOAhsHolePort2::HP2Rotx
Enter a value to rotate the port about the X-axis.
IJOAhsHolePort2::HP2Roty
Enter a value to rotate the port about the Y-axis.
IJOAhsHolePort2::HP2Rotz
Enter a value to rotate the port about the Z-axis.
IJOAhsHolePort2::HP2PosX
Enter the position, from the plates bottom left (0,0,0), in the X direction.
IJOAhsHolePort2::HP2PosY
Enter the position, from the plates bottom left (0,0,0), in the Y direction.
IJOAhsHolePort2::HP2Size
Enter the size of the hole.
IJOAhsHolePort3::HP3Rotx
Enter a value to rotate the port about the X-axis.
IJOAhsHolePort3::HP3Roty
Enter a value to rotate the port about the Y-axis.
IJOAhsHolePort3::HP3Rotz
Enter a value to rotate the port about the Z-axis.
IJOAhsHolePort3::HP3PosX
Enter the position, from the plates bottom left (0,0,0), in the X direction.
IJOAhsHolePort3::HP3PosY
Enter the position, from the plates bottom left (0,0,0), in the Y direction.
IJOAhsHolePort3::HP3Size
Enter the size of the hole.