Plate Properties - Intergraph Smart 3D - Reference Data

Intergraph Smart 3D Hangers and Supports SmartParts Configuration

Language
English
Product
Intergraph Smart 3D
Subproduct
3D Symbols
Search by Category
Reference Data
Smart 3D Version
12.1 (2019)

These properties specify the plate properties for the block clamp.

IJUAhsThickness1::Thickness1

Specifies the thickness of the top plate. If this value is set to zero, the top plate is not shown.

IJUAhsLength1::Length1

Specifies the length of the top plate.

IJUAhsWidth1::Width1

Specifies the width of the top plate.

IJUAhsThickness2::Thickness2

Specifies the thickness of the bottom plate. If this value is set to zero, the bottom plate is not shown.

IJUAhsLength2::Length2

Specifies the length of the bottom plate.

IJUAhsWidth2::Width2

Specifies the width of the bottom plate.

IJUAhsMidPlateBotShape::MidPlateBotShape

Specifies the name of the middle bottom plate shape. If more than two pipes are supported, the pipe holes or dents are not shown.

The following middle bottom shapes are supported:

IJUAhsMidPlateTopShape::MidPlateTopShape

Specifies the name of the middle top plate shape. If more than two pipes are supported, the pipe holes or dents are not shown.

The following middle top shapes are supported:

IJUAhsThickness3::Thickness3

Specifies the thickness of the base plate. If this value is set to zero or not provided, the base plate is not shown.

IJUAhsLength3::Length3

Specifies the length of the base plate.

IJUAhsWidth3::Width3

Specifies the width of the base plate.

IJUAhsThickness4::Thickness4

Specifies the thickness of the vertical plate or stanchion. Thickness4 must be greater than zero, or the vertical plate or stanchion is not shown.

IJUAhsLength4::Length4

Specifies the length of the vertical plate. If Length4 is set to zero, a stanchion is drawn instead of a vertical plate.

IJUAhsWidth4::Width4

Specifies the width of the vertical plate. If Length4 is set to zero, Width4 specifies the diameter of the stanchion.

IJUAhsThickness5::Thickness5

Specifies the thickness of channel clips. Channel clips are only shown when Thickness5 is greater than zero.

IJUAhsLength5::Length5

Specifies the length of channel clips.

IJUAhsWidth5::Width5

Specifies the width of channel clips.

IJUAhsWidth6::Width6

Specifies the distance between channel clips.

IJUAhsPin1::Pin1Length

Specifies the length of the bolt. Pin1Diameter and Pin1Length must be greater than zero for the bolts to be shown.

IJUAhsPin1::Pin1Diameter

Specifies the diameter of the bolt. Pin1Diameter and Pin1Length must be greater than zero for the bolts to be shown.

IJUAhsHeight1::Height1

Specifies the distance from the pipe centerline of the first pipe to the top of the block clamp.

IJUAhsHeight2::Height2

Specifies the distance from the pipe centerline of the first pipe to the bottom of the block clamp.

IJUAhsOffset1::Offset1

Specifies the lateral offset of block clamp if it is not centered on the pipe. If there is more than one pipe, Offset1 specifies the distance between the pipes.

IJUAhsOffset2::Offset2

Specifies the lateral distance from the center of the pipe to the edge of the block. Offset2 is used if there is only one pipe and Offset1 is set to zero.

IJUAhsOffset3::Offset3

Specifies the distance between blocks. Offset3 is used only if there are two blocks. If Offset3 is less than the block Width, then only one block is shown. Also, if Offset3 is greater than or equal to the block Width, then two blocks are shown.