Rich Hanger Beam Properties
Basic Steel Properties
These attributes define the common properties of hanger beam steel.
IJOAHsHgrBeamType::HgrBeamType
Specifies whether the hanger beam is Cutback steel or Snipped steel. HgrBeamType is a codelisted value. Allowed values are from HS_System_Codelist.xls are 1- Cutback Steel and 2 - Snipped Steel.
-
Cutback steel is not supported for circular cross sections, such as HSSR and Pipe.
-
Snipped steel is only supported for an L cross section.
IJUAhsOccOverLength:: BeginOverLength
Specifies the over length at the beginning of the steel. BeginOverLength can be either positive or negative.
IJUAhsOccOverLength:: EndOverLength
Specifies the over length at the end of the steel. EndOverLength can be either positive or negative.
IJUAhsOccLength::Length
Specifies the length of the steel. The software calculates Length using the start and end points in the graphic when you place the steel.
IJUAhsVarLength::VarLength
Specifies the cut length of the steel when you apply cutback angles, snip angles, or overlength on the steel.
Use the following properties to map and retrieve the geometry information from structural workbook, StructCrossSections-<Standard Name>.xls.
HgrRelation(i):ClassName
Specifies the cross section type. Example, L, C, W, and so on.
HgrRelation(i):Standard
Specifies the standard name. It is a codelisted value from HS_System_Codelist.xls. For example, AISC, CISC, Japan, China, Aust, and so on.
tHgrRelation(i):SectionName
Specifies the section name. Use the SecionName from StructCrossSections-<Standard Name>.xls. For example, HSS32x24x.625, C15x50, L8x8x1-1/8, and so on.
IJOAhsReflect::Reflect
Specifies the plane for the reflection of Rich Hanger Beam. The following codelist values are available in the hsReflectType sheet of the HS_S3DParts_Codelist workbook.
-
0 - No
-
1 - Along Flange Plane
-
2 - Along Web Plane
IJOAhsReflect::ReflectPlaneOffset
Specifies the offset for the Reflect Plane from the Cardinal Point 1 of the section.
Cutback Steel Properties
These attributes define the cutback steel properties.
IJOAhsCutback::BeginCutbackAnchorPoint
Specifies the edge for the cutback at the begin face. The codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are 2 - Bottom Center, 4 - Left Center, 6 - Right Center, and 8 - Top Center
IJOAhsCutback::EndCutbackAnchorPoint
Specifies the edge for the cutback at the end face. The codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are 2 - Bottom Center, 4 - Left Center, 6 - Right Center, and 8 - Top Center
IJOAhsCutback:: CutbackBeginAngle
Specifies the start cutback angle for the steel. For CutbackAnchorPoint set to 2 or 8, the face ports rotate by the cutback angle and align along the cutback face.
IJOAhsCutback::CutbackEndAngle
Specifies the end cutback angle for the steel. For CutbackAnchorPoint set to 2 or 8, the face ports rotate by the cutback angle and align along the cutback face.
Angle Value |
Attribute Populated |
Anchor Point |
Result |
---|---|---|---|
+ve |
CutbackBeginAngle |
2 |
Adds specified degrees |
+ve |
CutbackBeginAngle |
4 |
Subtracts specified degrees |
+ve |
CutbackBeginAngle |
6 |
Adds specified degrees |
+ve |
CutbackBeginAngle |
8 |
Subtracts specified degrees |
-ve |
CutbackBeginAngle |
2 |
Subtracts specified degrees |
-ve |
CutbackBeginAngle |
4 |
Adds specified degrees |
-ve |
CutbackBeginAngle |
6 |
Subtracts specified degrees |
-ve |
CutbackBeginAngle |
8 |
Adds specified degrees |
+ve |
CutbackEndAngle |
2 |
Subtracts specified degrees |
+ve |
CutbackEndAngle |
4 |
Adds specified degrees |
+ve |
CutbackEndAngle |
6 |
Subtracts specified degrees |
+ve |
CutbackEndAngle |
8 |
Adds specified degrees |
-ve |
CutbackEndAngle |
2 |
Adds specified degrees |
-ve |
CutbackEndAngle |
4 |
Subtracts specified degrees |
-ve |
CutbackEndAngle |
6 |
Subtracts specified degrees |
-ve |
CutbackEndAngle |
8 |
Adds specified degrees |
Snipped Steel Properties
These properties specify the Flange and Web modifications when a hanger is snipped by various offset values and angles.
IJOAhsSnipedSteel::CutbackBeginAngle1
Specifies the angle with which the begin face of the flange is snipped.
IJOAhsSnipedSteel::CutbackBeginAngle2
Specifies the angle with which the begin face of the web is snipped.
IJOAhsSnipedSteel::CutbackEndAngle1
Specifies the angle with which the end face of the flange is snipped.
IJOAhsSnipedSteel::CutbackEndAngle2
Specifies the angle with which the end face of the web is snipped.
IJOAhsSnipedSteel::BeginCutbackAnchorPoint1
Specifies the edge for the cutback at the begin face of the flange. The following codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are valid:
-
2 - Bottom Center
-
8 - Top Center. BeginCutbackAnchorPoint1 (read-only value)
IJOAhsSnipedSteel::BeginCutbackAnchorPoint2
Specifies the edge for the cutback at the begin face of the web. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:
-
4 - Left Center
-
6 - Right Center. BeginCutbackAnchorPoint2 (read-only value)
IJOAhsSnipedSteel::EndCutbackAnchorPoint1
Specifies the plane for the cutback at the end face of the flange. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:
-
2 - Bottom Center
-
8 - Top Center. EndCutbackAnchorPoint1 (read-only value)
IJOAhsSnipedSteel::EndCutbackAnchorPoint2
Specifies the edge for the cutback at the end face of the web. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:
-
4 - Left Center
-
6 - Right Center. EndCutbackAnchorPoint2 (read-only value)
IJOAhsCutbackOffset::BeginOffsetAlongFlange
Specifies the offset with which the begin face of the flange is snipped.
IJOAhsCutbackOffset::BeginOffsetAlongWeb
Specifies the offset with which the begin face of the web is snipped.
IJOAhsCutbackOffset::EndOffsetAlongFlange
Specifies the offset with which the end face of the flange is snipped.
IJOAhsCutbackOffset::EndOffsetAlongWeb
Specifies the offset with which the end face of the web is snipped.
IJOAhsFacePortOrient::FacePortOrient
Specifies whether the face port orientation is aligned along the flange, or the web when a snip angle is applied. It is a codelisted value from the hsFacePortOrient sheet in the HS_System_Codelist.xls workbook. Allowed values are: 1 - Face Port Orient Along Flange and 2 - Face Port Orient Along Web.
Port Properties
IJOAhsSteelCP::CP1
Specifies the cardinal point of the BeginCap port. The default location of CP1 is 1.
IJOAhsSteelCP::CP2
Specifies the cardinal point of the EndCap port. The default location of CP2 is 1.
IJOAhsSteelCP::CP3
Specifies the cardinal point of the BeginFace port. The default location of CP3 is 5.
IJOAhsSteelCP::CP4
Specifies the cardinal point of the EndFace port. The default location of CP4 is 5.
IJOAhsSteelCP::CP5
Specifies the cardinal point of the Neutral port. The default location of CP5 is 5.
IJOAhsSteelCP::CP6
Specifies the cardinal point of the BeginFlex port. The default location of CP6 is 8.
IJOAhsSteelCP::CP7
Specifies the cardinal point of the EndFlex port. The default location of CP7 is 8.
IJOAhsBeginCap::BeginCapXOffset
Specifies the offset with which the BeginCap port is moved in the x-axis.
IJOAhsBeginCap::BeginCapYOffset
Specifies the offset with which the BeginCap port is moved in the y-axis.
IJOAhsBeginCap::BeginCapRotZ
Specifies the angle with which the BeginCap port is rotated about its z-axis.
IJOAhsEndCap::EndCapXOffset
Specifies the offset with which the EndCap port is moved in the x-axis.
IJOAhsEndCap::EndCapYOffset
Specifies the offset with which the EndCap port is moved in the y-axis.
IJOAhsEndCap::EndCapRotZ
Specifies the angle with which the EndCap port is rotated about its z-axis.
IJOAhsFlexPort::FlexPortXOffset
Specifies the offset with which the BeginFlex port is moved in the x-axis.
IJOAhsFlexPort::FlexPortYOffset
Specifies the offset with which the BeginFlex port is moved in the y-axis.
IJOAhsFlexPort::FlexPortZOffset
Specifies the offset with which the BeginFlex port is moved in the z-axis.
IJOAhsFlexPort::FlexPortRotX
Specifies the angle with which the BeginFlex port is rotated about its x-axis.
IJOAhsFlexPort::FlexPortRotY
Specifies the angle with which the BeginFlex port is rotated about its y-axis.
IJOAhsFlexPort::FlexPortRotZ
Specifies the angle with which the BeginFlex port is rotated about its z-axis.
IJOAhsEndFlexPort::EndFlexPortXOffset
Specifies the offset with which the EndFlex port is moved in the x-axis.
IJOAhsEndFlexPort::EndFlexPortYOffset
Specifies the offset with which the EndFlex port is moved in the y-axis.
IJOAhsEndFlexPort::EndFlexPortZOffset
Specifies the offset with which the EndFlex port is moved in the z-axis.
IJOAhsEndFlexPort::EndFlexPortRotX
Specifies the angle with which the EndFlex port is rotated about its x-axis.
IJOAhsEndFlexPort::EndFlexPortRotY
Specifies the angle with which the EndFlex port is rotated about its y-axis.
IJOAhsEndFlexPort::EndFlexPortRotZ
Specifies the angle with which the EndFlex port is rotated about its z-axis.