The following properties define the basic geometry of the guide.
IJUAhsWidth1::Width1
Specifies the width of the base plate. Width1 is required if Thickness1 > 0.
IJUAhsLength1::Length1
Specifies the depth of the base plate. Length1 is required if Thickness2 > 0.
IJUAhsThickness1::Thickness1
Specifies the thickness of the base plate. If Thickness1 < 0, the base plate is not included.
IJUAhsWidth2::Width2
Specifies the width of the vertical plate.
IJUAhslength2::Length2
Specifies the length of the vertical plate.
IJUAhsThickness2::Thickness2
Specifies the thickness of the vertical plate.
-
Thickness2 is required if vertical steel is not used.
-
Thickness2 is required if vertical steel is used and section configuration is vertical.
IJUAhsWidth3::Width3
Specifies the width of the horizontal plate.
IJUAhsLength3::Length3
Specifies the depth of the horizontal plate.
IJUAhsThickness3::Thickness3
Specifies the thickness of the horizontal plate. Thickness3 is used only when GuideHeight is less than Thickness2.
IJUAhsWidth4::Width4
Specifies the width of the block plate.
IJUAhsLength4::Length4
Specifies the depth of the block plate.
IJUAhsThickness4::Thickness4
Specifies the thickness of the block plate.
IJUAhsOffset1::Offset1
Specifies the distance between the edges of the horizontal and the vertical plate.
IJUAhsGap1::Gap1
Specifies the gap between two vertical plates or between the cardinal points of the steel sections.
IJUAhsGuideHeight::GuideHeight
Specifies the distance between the bottom edge of the vertical plate and top edge of the horizontal plate.When the GuideHeight is provided, Thickness3 value is ignored and calculated as Thickness3 = GuideHeight - Thickness2.
VerPlSecStand, VerPlSecSize and VerPlSecType are optional if vertical steel sections are not used.
IJUAhsVerPlSecStand::VerPlSecStand
Specifies the section standard for the vertical plate.
IJUAhsVerPlSecSize::VerPlSecSize
Specifies the section size for vertical the plate.
IJUAhsVerPlSecType::VerPlSecType
Specifies the section type for vertical the plate.
IJUAhsAngle1::Angle1
Specifies the rotation angle of the first vertical section along its longitudinal axis.
IJUAhsAngle2::Angle2
Specifies the rotation angle of the second vertical section along its longitudinal axis.
-
Each angle is applied about the cardinal point specified.
-
The angle is ignored if the section is not specified or a plate is used instead.
IJUAhsConnection1::Connection1
Specifies the cardinal point of the first vertical section. It determines the connection point of the steel section.
For more information, see the CrossSectionCardinalPoints codelist in the Allcodelists.xls.
IJUAhsConnection2::Connection2
Specifies the cardinal point of the second vertical section. It determines the connection point of the steel section.
For more information, see the CrossSectionCardinalPoints codelist in the Allcodelists.xls.
IJUAhsMirrored1::Mirrored1
Indicates whether the first vertical steel section is mirrored about the specified cardinal point. If not specified, the section is not mirrored.
IJUAhsMirrored2::Mirrored2
Indicates whether the second vertical steel section is mirrored about the specified cardinal point.If not specified, the section is not mirrored.
IJUAhsSecConfig::SecConfig
Specifies if the vertical steel section is vertical or horizontal.
-
Length2 is required if SecConfig is horizontal.
-
Thickness2 is required if SecConfig is Vertical.
IJUAhsHorPlSecStand::HorPlSecStand
Specifies the section standard for the horizontal plate.
IJUAhsHorPlSecSize::HorPlSecSize
Specifies the section size for the horizontal plate.
IJUAhsHorPlSecType::HorlSecType
Specifies the section type for the horizontal plate.
IJUAhsCPXOffset::CPXOffset
Specifies the offset of the cross section shape with respect to the cardinal point horizontally. CPXOffset is required when cross section is rotated.
IJUAhsCPYOffset::CPYOffset
Specifies the offset of the cross section shape with respect to the cardinal point vertically.
IJUAhsAngle3::Angle3
Specifies the rotation angle of the first horizontal section along its longitudinal axis.
IJUAhsAngle4::Angle4
Specifies the rotation angle of the second horizontal section along its longitudinal axis.
IJUAhsConnection3::Connection3
Specifies the cardinal point of the second horizontal section. It determines the connection point of the steel section.
For more information, see the CrossSectionCardinalPoints codelist in the Allcodelists.xls.
IJUAhsConnection4::Connection4
Specifies the cardinal point of the second horizontal section. Determines the connection point of the steel section.
For more information, see the CrossSectionCardinalPoints codelist in the Allcodelists.xls.
IJUAhsOffset2::Offset2
Specifies the offset value of the horizontal section from the connection point.
HorPlSecStand, HorPlSecSize and HorPlSecType are optional and not required if Length3, Width3 and Thickness3 are defined. Length3 and Thickness3 are optional and not required if HorPlSecStand, HorPlSecSize and HorPlSecType are defined.
IJUAhsSolidBaseVerPl::SolidBaseVerPl
Specifies which solid shapes would be used to create the base plate and the vertical plate. This attribute uses the YES/NO codelist.
-
YES – Base plate and vertical plate are one solid shape.
-
NO –Separate solid shapes are used to create base plate and vertical plate.
IJUAhsSolidVerHorPl::SolidVerHorPl
Specifies which solid shapes are used to create horizontal plate and vertical plate. This attribute uses the YES/NO codelist.
-
YES – Vertical and horizontal plates are one solid shape.
-
NO –Separate solid shapes are used to create the horizontal and the vertical plate.
Using the above properties different combinations of base, horizontal and vertical plates can be defined.