COMPONENT-INFORMATION-FILE section - Isogen

Provides a cross-reference to entries in the Component Information File (CIF) by defining the layout and content of that file.

The section heading COMPONENT-INFORMATION-FILE is followed by the following identifiers and associated data.

ITEM-CODE-IDENTIFIER

N.S.

N.S.SEC

N.S.THIRD

N.S.THICKNESS/RATING

N.S.SEC.THICKNESS/RATING

N.S.WALL-THICKNESS

N.S.SEC.WALL-THICKNESS

DESCRIPTION

COMPONENT-WEIGHT

COMPONENT-CONTENT-WEIGHT

EQUIVILANT-INSULATION-LENGTH

N.S.CONVERSION-CODE

RADIUS-DIAMETERS

RADIUS-MM

RADIUS-INCH

DETAILED-SKETCH

INFORMATION-NOTE

COMPONENT-ATTRIBUTE1 to COMPONENT-ATTRIBUTE10 (-190 tom -199)

MATERIAL-ATTRIBUTE1 to MATERIAL-ATTRIBUTE10 (-80 to -89)

User Defined Names matching those used in the PCF file

DELIMITER-CHARACTER data - Where data specifies the delimiter used in the COMPONENT-INFORMATION-FILE.

Each of the following is followed by either start-col. end-col. or position in file, depending on whether a delimiter character is set.

The actual number of these data items present will depend upon which of the available facilities are being used.
The maximum width of the file is 500 characters and any characters outside this limit are ignored.

COMPONENT-INFORMATION-FILE section - Isogen - Help

Isogen Configuration Help

FDF Identifier	Used For	Used For
ITEM-CODE- IDENTIFIER	1) Design contractors item code. 2) Fabricator's item code.	2) Fabricator's item code.
N.S.	The main bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.	The main bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.
N.S.SEC	The secondary bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.	The secondary bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.
N.S.THIRD	A third bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.	A third bore of a component. Specified in accordance with the UNITS-BORE identifier in the UNITS-DEFINITION section of the FDF.
N.S.THICKNESS/ RATING	Thickness/Rating for the main bore of a component.	Thickness/Rating for the main bore of a component.
N.S.SEC.THICKNESS /RATING	Thickness/Rating for the secondary bore of a component.	Thickness/Rating for the secondary bore of a component.
N.S.OUTSIDE- DIAMETER	The outside diameter of the main bore of the component.	The outside diameter of the main bore of the component.
N.S.SEC.OUTSIDE- DIAMETER	The outside diameter of the secondary bore of the component.	The outside diameter of the secondary bore of the component.
N.S.WALL-THICKNESS	The wall thickness of the main bore of the component.	The wall thickness of the main bore of the component.
N.S.SEC.WALL- THICKNESS	The wall thickness of the secondary bore of the component.	The wall thickness of the secondary bore of the component.
DESCRIPTION	Fabricator's material descriptions.	Fabricator's material descriptions.
COMPONENT-WEIGHT	The weight of a component - in the weight units specified in accordance with the UNITS-WEIGHT identifier in the UNITS-DEFINITION section of the FDF.	The weight of a component - in the weight units specified in accordance with the UNITS-WEIGHT identifier in the UNITS-DEFINITION section of the FDF.
COMPONENT-CONTENT- WEIGHT	The weight of the components water volume specified in accordance with the UNITS-WEIGHT identifier in the UNITS- DEFINITION section of the FDF. For PIPE, the weight specified here’s the weight per unit length for the length units specified in the UNITS-LENGTH identifier in the UNITS-DEFINITION section of the FDF.	The weight of the components water volume specified in accordance with the UNITS-WEIGHT identifier in the UNITS- DEFINITION section of the FDF. For PIPE the weight specified here’s the weight per unit length for the length units specified in the UNITS-LENGTH identifier in the UNITS-DEFINITION section of the FDF.
EQUIVAENT- INSULATION-LENGTH	Used to equate the component insulation weight to a length-based weight. Values here are the equivalent length of insulation in accordance with the weight and length units in the UNITS-LENGTH and UNITS-WEIGHT identifiers in the UNITS-DEFINITION section of the FDF.	Used to equate the component insulation weight to a length based weight. Values here are the equivalent length of insulation in accordance with the weight and length units in the UNITS-LENGTH and UNITS-WEIGHT identifiers in the UNITS-DEFINITION section of the FDF.
N.S.CONVERSION-CODE	This is used where the N.S. and N.S. Header output on the Weld list and Weld summary outputs is to be replaced by a user supplied code.	This is used where the N.S. and N.S. Header output on the Weld list and Weld summary outputs is to be replaced by a user supplied code.
RADIUS-DIAMETERS	Bend radius specified as a number of diameters.	Bend radius specified as a number of diameters.
RADIUS-MM	Bend radius specified in millimeters.	Bend radius specified in millimeters.
RADIUS-INCH	Bend radius specified in millimeters.	Bend radius specified in millimeters.
DETAILED-SKETCH	Detail sketch file name.	Detail sketch file name.
INFORMATION-NOTE	Information note name.	Information note name.
COMPONENT- ATTRIBUTE1 to COMPONENT- ATTRIBUTE10	Data for component attributes.	Data for component attributes.
MATERIAL-ATTRIBUTE1 to MATERIAL- ATTRIBUTE10	Data for material attributes.	Data for material attributes.
User-defined names matching those used in the PCF file.	Data for user-defined names.	Data for user-defined names.