The following attributes are used only if an Anchor Bolt part has been specified:
Name |
User Name |
Category |
On Property Page |
Read Only |
---|---|---|---|---|
AnchorBoltX |
Anchor Bolt Spacing X |
Dimensions |
Yes |
No |
AnchorBoltXSelection |
Anchor Bolt Spacing X Selection |
Dimensions |
No |
Yes |
AnchorBoltXRule |
Anchor Bolt Spacing X Rule |
Dimensions |
No |
Yes |
AnchorBoltXDefinition |
Anchor Bolt Spacing X Definition |
Dimensions |
No |
Yes |
AnchorBoltY |
Anchor Bolt Spacing Y |
Dimensions |
Yes |
No |
AnchorBoltYSelection |
Anchor Bolt Spacing Y Selection |
Dimensions |
No |
Yes |
AnchorBoltYRule |
Anchor Bolt Spacing Y Rule |
Dimensions |
No |
Yes |
nchorBoltYDefinition |
Anchor Bolt Spacing Y Definition |
Dimensions |
No |
Yes |
AnchorBoltZ |
Anchor Bolt Spacing Z |
Dimensions |
Yes |
No |
AnchorBoltZSelection |
Anchor Bolt Spacing Z Selection |
Dimensions |
No |
Yes |
AnchorBoltZRule |
Anchor Bolt Spacing Z Rule |
Dimensions |
No |
Yes |
AnchorBoltZDefinition |
Anchor Bolt Spacing Z Definition |
Dimensions |
No |
Yes |
Attribute Name |
Description |
Implementation Details |
IJUAhsAnchorBoltX:: |
A numerical value for distance that will determine the X spacing between the bolts. If you intend to use AnchorBoltXRule to determine the value of the value, then this attribute should be left blank. |
Default units are as specified on the CustomInterfaces sheet. Specify the units otherwise. IE: |
IJUAhsAnchorBoltXRl:: |
An HgrSupportRule that returns a numerical value for the distance that will determine the X spacing between the bolts. The Hanger Rule should be present in the catalog; it can be a rule Name or ProgID. The rule must return the value in the DB Units (meters). If you intend to use AnchorBoltX to directly specify the value then this attribute should be left blank. |
IE: Rule Name Rule ProgID |
IJUAhsAnchorBoltXSel:: |
A codelist value that determines where to get the value from. Uses hsSelection codelist from HS_S3DAssy_Codelist.xls |
hsSelection 1 = By Rule 2 = By Input |
IJUAhsAnchorBoltXDef:: |
The definition of the Anchor Bolt X Spacing. This attribute specifies how the Anchor Bolt X Spacing should be measured. Supported values are shown to the right. Additional definitions can be added to the AIR as needed. If an unsupported definition value is entered, or the attribute is left blank then an error will occur and the support will fail. |
Supported values 1 – Edge of Plate to Center of bolt 2 – Center of Bolt to Center of Bolt 3 – Center of Plate to Center of Bolt |
IJUAhsAnchorBoltY:: |
A numerical value for distance that will determine the Y spacing between the bolts. If you intend to use AnchorBoltYRule to determine the value of the value, then this attribute should be left blank. |
Default units are as specified on the CustomInterfaces sheet. Specify the units otherwise. IE: |
IJUAhsAnchorBoltYRl:: |
An HgrSupportRule that returns a numerical value for the distance that will determine the Y spacing between the bolts. The Hanger Rule should be present in the catalog; it can be a rule Name or ProgID. The rule must return the value in the DB Units (meters). If you intend to use AnchorBoltY to directly specify the value then this attribute should be left blank. |
IE: Rule Name Rule ProgID |
IJUAhsAnchorBoltYSel:: |
A codelist value that determines where to get the value from. Uses hsSelection codelist from HS_S3DAssy_Codelist.xls |
hsSelection 1 = By Rule 2 = By Input |
IJUAhsAnchorBoltYDef:: |
The definition of the Anchor Bolt Y Spacing. This attribute specifies how the Anchor Bolt Y Spacing should be measured. Supported values are shown to the right. Additional definitions can be added to the AIR as needed. If an unsupported definition value is entered, or the attribute is left blank then an error will occur and the support will fail. |
Supported values 1 – Edge of Plate to Center of bolt 2 – Center of Bolt to Center of Bolt 3 – Center of Plate to Center of Bolt |
IJUAhsAnchorBoltZ:: |
A numerical value for distance that will determine the Z spacing of the bolts. If you intend to use AnchorBoltZRule to determine the value, then this attribute should be left blank. |
Default units are as specified on the CustomInterfaces sheet. Specify the units otherwise. IE: |
IJUAhsAnchorBoltZRl:: |
An HgrSupportRule that returns a numerical value for the distance that will determine the Z spacing of the bolts. The Hanger Rule should be present in the catalog; it can be a rule Name or ProgID. The rule must return the value in the DB Units (meters). If you intend to use AnchorBoltZ to directly specify the value then this attribute should be left blank. |
IE: Rule Name Rule ProgID |
IJUAhsAnchorBoltZSel:: |
A codelist value that determines where to get the value from. Uses hsSelection codelist from HS_S3DAssy_Codelist.xls |
hsSelection 1 = By Rule 2 = By Input |
IJUAhsAnchorBoltZDef:: |
The definition of the Anchor Bolt Z value. This attribute specifies how the Anchor Bolt Z value should be measured. Supported values are shown to the right. Additional definitions can be added to the AIR as needed. If an unsupported definition value is entered, or the attribute is left blank then an error will occur and the support will fail. |
Supported values 1 – From Surface of Base Plate |