These properties specify and customize the main steel member in the support.
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsMember1::Member1Part |
Specifies the steel part number to use for the main support section. The part number specified must be a rich hanger beam. To select the part number using Member1Rule, do not type any value for this property. |
|
IJUAhsMember1Rl::Member1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. The hanger rule must exist in the catalog; it can be the name of a rule, or a rule ProgID. To select a part number directly using Member1Part, do not type any value for this property. |
Option 1 - Specify a part number or part class directly. Option 2 - Use HgrRule to get the part. The base support is a mandatory part. Specify either a Member1Part or Member1Rule. |
IJUAhsMember1Ang::Member1OrientationAngle |
Specifies the angle of rotation for the main member. The angle is about the member's axis. |
The following values are allowed: |
IJUAhsMember1EndOH::Member1EndOverhangValue |
Defines the distance that the main section should overhang past the second leg. To specify the overhang value using Member1EndOverhangRule, do not type any value for this property. |
|
IJUAhsMember1EndOHRl::Member1EndOverhangRule |
Defines an HgrSupportRule that returns the distance that the main section should overhang past the second leg. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the overhang value directly using Member1EndOverhangValue, do not type any value for this property. |
|
IJUAhsMember1EndOHDef::Member1EndOverhangDefinition |
Defines how the EndOverhang should be measured. This property is applicable to U, I and L Frame types. The following values are allowed: |
|
IJUAhsMember1EndOHSel::Member1EndOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select the Member1EndOverhang by either input or rule. The following values are allowed: |
By Rule - 1 – Member1EndOverhangRule is used By Input - 2 – Member1EndOverhangValue is used |
IJUAhsCapPlate1::CapPlate1Part |
Specifies the part number or the part class of the plate placed at the end of the main section and at the end connected to the first leg. This must be a SmartPart 2 Port Plate. To select the part using CapPlate1Rule, do not type any value for this property. |
|
IJUAhsCapPlate1Rl::CapPlate1Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate1Part, do not type any value for this property. CapPlate1Rule can also be used to specify a custom part selection rule. If both CapPlate1Part and CapPlate1Rule are populated, then it is assumed that CapPlate1Rule is a part selection rule, which will then be used to override the default part selection rule defined in the catalog for the part class specified in CapPlate1Part. |
|
IJUAhsCapHorOffset::CapHorOffset |
Specifies the horizontal offset of the CapPlate1 |
|
IJUAhsCapVerOffset::CapVerOffset |
Specifies the Vertical offset of the CapPlate1 |
|
IJUAhsCapPlate1Ang::CapPlate1Angle |
Specifies the angle that CapPlate1 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |