If you specify a Bending file in the FLS file or a –127 record in the Spoolgen OPT file, the software reads the generated file, consolidates it, and then creates three intrinsic recordsets: Bends, CutPieces, and Holes. These three recordsets are processed in the same way as other intrinsic recordsets created from the Material Control, Welding, Spool Information or Repeatability files.
Bends Recordset
Field |
Description |
PIPELINE |
Indicates the pipeline reference (*). |
SPOOL-ID |
Indicates the spool ID (*). |
CUT-ID |
Indicates the cut piece ID (*). |
PIPING-SPEC |
Indicates the piping specification (*). |
ITEM-CODE |
Indicates the pipe item code (*). |
ND |
Indicates the nominal diameter (*). |
UMI |
Indicates the generated unique material identifier. Used to link to other tables (*). |
NUMBER |
Indicates the bend number. |
X |
Indicates the bend position. |
Y |
|
Z |
|
RADIUS |
Indicates the bend radius. |
ANGLE |
Indicates the bend angle. |
CutPieces Recordset
Field |
Description |
PIPELINE |
Indicates the pipeline reference (*). |
SPOOL-ID |
Indicates the spool ID (*). |
PIPING-SPEC |
Indicates the piping specification (*). |
ITEM-CODE |
Indicates the item code. (*). |
ND |
Indicates the nominal diameter (*). |
UMI |
Indicates the generated unique material identifier. Used to link to other tables (*). |
START-X |
Indicates the start point. |
START-Y |
|
START-Z |
|
FINISH-X |
Indicates the end point. |
FINISH-Y |
|
FINISH-Z |
|
CUT-ID |
Indicates the cut piece ID. |
PART-NUMBER |
Indicates the part number. |
OD |
Indicates the outside diameter. |
WALL-THICKNESS |
Indicates the pipe thickness (if set). |
CUT-LENGTH |
Indicates the total length. |
DEV-LENGTH |
Indicates the developed length (allowing for weld gaps, and so on). |
START-COMPONENT |
Indicates the start component type (flange, for example). |
START-COMP-CODE |
Indicates the start component item code. |
START-COMP-PART-NO |
Indicates the part number. |
START-COMP-LENGTH |
Indicates the length. |
START-END-TYPE |
Indicates the IDF record number (Flange=105, for example). |
FINISH-COMPONENT |
Indicates the finish component type (flange, for example). |
FINISH-COMP-CODE |
Indicates the finish component item code. |
FINISH-COMP-PART-NO |
Indicates the component part number. |
FINISH-COMP-LENGTH |
Indicates the component length. |
FINISH-END-TYPE |
Indicates the IDF record number (Flange=105, for example). |
NUM-HOLES-TO-BE-CUT |
Indicates the number of holes in cut piece. |
Holes Recordset
Field |
Description |
PIPELINE |
Indicates the pipeline reference (*). |
SPOOL-ID |
Indicates the spool ID (*). |
PIPING-SPEC |
Indicates the piping specification (*). |
ITEM-CODE |
Indicates the item code (*). |
ND |
Indicates the nominal diameter. |
UMI |
Indicates the generated unique material identifier. Used to link to other tables (*). |
HOLE-NUM |
Indicates the hole number. |
HOLE-COMP-PART-NO |
Indicates the part for component with hole. |
HOLE-DIAMETER |
Indicates the hole diameter. |
HOLE-INTSECN-ANGLE |
Indicates the intersection angle. |
HOLE-CENTRE-OFFSET |
Indicates the offset. |
HOLE-ROTATION-ANGLE |
Indicates the rotation angle. |
HOLE-DISTANCE |
Indicates the distance from cut piece start. |
-
Fields marked with an asterisk ( * ) are always present. Other fields are present depending on the content of the Bending file (which is subject to change). The Bends and Holes recordsets are not created if there are no bends (pulled bends) or holes in the Isogen data.
-
See the Isogen documentation for a full description of these parameters.