These properties define the geometry of the yoke portion of the yoke clamp.
IJUAhsHeight3::Height3
Specifies the distance from the pipe centerline to the lower face of the yoke.
If the distance is <= 0 then the software sets 0.25 times the Diameter1 to the default value for this property.
IJUAhsHeight4::Height4
Specifies the distance from the pipe centerline to the lower flat spot of the yoke.
This value is always greater than Height3. If it is less than or equal to Height3, then the software sets Height3 plus 2 times Pin1Diameter as the default value for this property.
IJUAhsHeight5::Height5
Specifies the distance from the pipe centerline to the top flat spot of the yoke.
This value is always greater than 0.5 times Diameter1. If it is less than or equal to 0.5 times Diameter1, then the software sets 0.5 times Diameter1 plus (Height4 minus Height3) as the default value for this property.
IJUAhsHeight6::Height6
Specifies the distance from the pin or lug centerline to the top of the yoke.
This value is always greater than 0.5 times Pin1Diameter. If it is less than or equal to 0.5 times Pin1Diameter, then the software sets 1.5 times Pin1Diameter as the default value for this property.
Type 1 & 2
Type 3 - Specifies the height of top block.
IJUAhsHeight7::Height7
Specifies the distance from the pipe centerline to the lower face of the yoke.
If Height7 is less than or equal to 0, then the software sets Height7 to Height5 minus (Height4 minus Height3) as the default value for this property.
If Height7 is less than 0.5 times Diameter1 and Height7 greater than 0, then the software sets Height7 to 0.5 times Diameter1 as the default value for this property.
IJUAhsLength3::Length3
Specifies the overall span of the yoke.
This value is always greater than UboltWidth plus UboltRodDia. If it is less than or equal to UboltWidth plus UboltRodDia, then the software sets UboltWidth plus 2 times UboltRodDia as the default value for this property.
IJUAhsLength4::Length4
Specifies the overall span of the upper attachment.
Case 1: if hsPinOrLug equals 1
-
It is always greater than zero.
-
If it is less than or equal to 0, then the software sets 1.5 times the Hole1Diameter as he default value for this property.
Case 2: if hsPinOrLug equals 2
-
It is always greater than zero.
-
If it is less than or equal to 0, then the software sets 0.5 times the Hole1Diameter as the default value for this property.
Case 3: If hsOrientation equals 2, then these dimensions are oriented parallel to the route.
-
It is always less than or equal to Width3.
-
If it is greater than Width3, then the software sets Width3 as the default value for this property.
hsPinOrLug = 1
hsPinOrLug = 2
hsPinOrLug = 3
IJUAhsLength5::Length5
Specifies the inside span of the upper attachment.
Case 1 if hsPinOrLug equals 1
-
It is always greater than zero and less than Length4.
-
If it isless than or equal to 0 or greater than Length4, then the software sets Hole1Diameteras the default value for this property.
Case 2: if hsPinOrLug equals 2 it is ignored.
Case 3: If hsOrientation equals 2, then these dimensions are oriented parallel to the route.
IJUAhsLength6::Length6
Specifies the inside span of the lower flat spot.
This value is always less than or equal to Length3 and greater than or equal to Length7. If it is zero or greater than Length3, then the software sets Length3 as the default value for this property.
If it is not equal to zero and less than Length7, then the software sets Length7 as the default value for this property.
IJUAhsLength7::Length7
Specifies the overall span of the top flat spot.
This value is always greater than or equal to Length5 and less than or equal to Length3. If it is less than Length5, then the software sets Length5 as the default value for this property.
If it is greater than Length3, then the software sets Length3 as the default value for this property.
IJUAhsWidth3::Width3
Specifies the width of the yoke body.
This value is always greater than or equal to Pin1Diameter. If it is less than Pin 1Diameter, then the software sets two times the Pin1Diameter as the default value for this property.
IJUAhsWidth4::Width4
Specifies the width of the pin or lug attachment.
This value is always greater than or equal to the Pin1Diameter. If it is less than Pin 1Diameter, then the software sets Width3 as the default value for this property.
If hsOrientation = 2, then these dimensions are also oriented perpendicular to the route.