General Tab (Wall Part Properties Dialog) - Intergraph Smart 3D - Help - Hexagon PPM

Intergraph Smart 3D Civil

Language
English
Product
Intergraph Smart 3D
Subproduct
Civil
Search by Category
Help
Smart 3D Version
13.1

Displays the wall properties that you can edit or that are automatically determined by the software at placement. The property name appears on the left side of the grid and the corresponding property value appears on the right side of the grid. If you selected more than one wall and then selected the properties command, only the common properties between the selected walls display.

When viewing properties for a single wall, the following properties display. More properties may display depending on what you defined in the reference data. Refer to the Structure Reference Data Help for more information on properties.

Category

Specifies the properties category to view. Select Standard, Weight and CG, and Dimensions.

Standard

The standard properties that display depend on the reference data for the wall. Because wall reference data is fully customizable, only the common properties are documented.

Parent System

Select the system to which the wall belongs.

Name

Displays the name of the wall. The wall name is based on the Naming Rule selection. If you want to type a new name for the wall, in the Naming Rule box, select User Defined, and then type a name for the wall in the Name box.

Naming Rule

Specify the naming rule that you want to use to name this wall.

Default Name Rule

Names the wall using the format "WallPart-<location>-<index>" where <location> is the global workshare location ID and <index> is a unique index number that starts at 0001. For example, WallPart-1-0043.

Unique Name Rule

Names the wall using the format "WallPart-<location>-<index>" where <location> is the global workshare location ID and <index> is a unique index number that starts at 0001. For example, WallPart-1-0043.

User Defined

Select to specify the wall part name yourself in the Name box.

Composition

Displays the composition of the wall.

Reporting Requirement

Specify whether or not this wall part is reported.

Reporting Type

Select the reporting requirements code for the wall part. Valid selections are defined in the Catalog task in the Reporting Type select list.

Dimensions

Total Volume

Specifies the volume of the slab or wall (length × width × height).

Net Volume

Specifies the volume of the wall minus the volumes of all openings in the wall.

Total Surface

Specifies the surface area of the slab or wall (top surface plus the bottom surface plus the side surfaces × length).

Net Surface

Specifies the surface area of the slab or wall minus the surface area of all the openings in the slab or wall.

Projected Surface

Specifies the surface area of the wall's bottom surface.

Net Projected Surface

Specifies the surface area of the wall's bottom surface minus the surface area of all openings in the wall.

Length

Specifies the object length.

Weight and CG

Displays the center-of-gravity and the weight of the selected object. The center-of-gravity locations are displayed relative to the active coordinate system along the X-, Y-, and Z-axes. The weight value that is displayed in the properties dialog box is calculated as the material density multiplied by the object's solid volume. Therefore, the material of the object affects the weight value that is displayed here. Check the material assigned to the object if the weight displayed is an improbable value. For the most accurate weight calculation, use the Tools > Run Reports command.

Dry Weight

Specifies the dry weight of the object.

Wet Weight

Specifies the wet weight of the object.

For equipment, the Weight and CG property Wet Weight is the sum of Dry Weight and Water Weight. The dry weight and water weight values are catalog properties defined on the part sheet for the equipment.

Dry CG X

Specifies the X-axis location of the dry center-of-gravity.

Dry CG Y

Specifies the Y-axis location of the dry center-of-gravity.

Dry CG Z

Specifies the Z-axis location of the dry center-of-gravity.

Wet CG X

Specifies the X-axis location of the wet center-of-gravity.

Wet CG Y

Specifies the Y-axis location of the wet center-of-gravity.

Wet CG Z

Specifies the Z-axis location of the wet center-of-gravity.

Fabrication and Construction

Fabrication Requirement

Specifies the fabrication requirement for the object. To change the options on the list, edit the Fabrication Type select list in Catalog.

Rule Driven

Specifies that a rule drives the value. This is the default option. Click to switch to User Driven .

User Driven

Allows you to select a value. Click to switch to Rule Driven .

Fabrication Type

Specifies the type of fabrication for the object. To change the options on the list, edit the Fabrication Type select list in Catalog.

Rule Controlled

Specifies that a rule defined for a parent property controls the value. If Rule Controlled does not display, you can select a value.

Construction Requirement

Specifies the construction requirement for the object. To change the options on the list, edit the Construction Requirement select list in Catalog.

Construction Type

Specifies the type of construction for the object. To change the options on the list, edit the Construction Type select list in Catalog.

Responsibility

Cleaning Responsibility

Specifies the party responsible for cleaning the object. To change the options on the list, edit the Cleaning Responsibility select list in Catalog.

Design Responsibility

Specifies the party responsible for designing the object. To change the options on the list, edit the Design Responsibility select list in Catalog.

Fabrication Responsibility

Specifies the party responsible for fabricating the object. To change the options on the list, edit the Fabrication Responsibility select list in Catalog.

Installation Responsibility

Specifies the party responsible for installing the object. To change the options on the list, edit the Installation Responsibility select list in Catalog.

Painting Responsibility

Specifies the party responsible for painting the object. To change the options on the list, edit the Painting Responsibility select list in Catalog.

Requisition Responsibility

Specifies the party responsible for ordering the object. To change the options on the list, edit the Requisition Responsibility select list in Catalog.

Supply Responsibility

Specifies the party responsible for delivering the object. To change the options on the list, edit the Supply Responsibility select list in Catalog.

Testing Responsibility

Specifies the party responsible for testing on the object. To change the options on the list, edit the Testing Responsibility select list in Catalog.